Woodturner's Resource
Woodturner's Resource  
  Featured Artist    Websites   Support Wr
Tutorials, Projects & Tips   Event Calendar   Tool and Book Store
  Home Page Forum HelpSearch Map TPT Resources LoginRegister
 
Pages: 1 2 
Send Topic Print
Beall polishing system (Read 832 times)
 
Bruce Kamp
Active Member
***
Offline


WR Rocks!

Posts: 173

Beall polishing system
Mar 25th, 2017 at 11:10am
 
I am considering buying the system. I do mostly bowls so I am looking at getting the three separate buffs with the MT2 extender vs the 3 in 1 setup.
To date I have been buffing my finishes using pumice and rotten stone using mineral oil as the lubricant and a felt pad as the buffer. This gets a little messy but not bad.
How do you feel the two methods will compare?
Thanks
Bruce
Back to top
  
 
IP Logged
 
Ron Carrabotta
WR Supporter
*****
Offline


WR Rocks!

Posts: 363

Dawsonville, ga, Georgia, USA
Dawsonville, ga
Georgia
USA

Gender: male

Jet 1014 VS
Jet 1642 -2EVS
Powermatic 3520B
Re: Beall polishing system
Reply #1 - Mar 25th, 2017 at 1:36pm
 
Bruce,

I've been using the Beall system since I got back into turning 7 years ago. I use it on almost all of my finished projects. I've also got the pads and mineral oil buffing system as well. Use the Beall 10x to1 vs the pads & oil. MUCH simpler.

Yes, for bowls get the separate buffs. You might want to consider getting both the wheels (original system) and the bowl buffs.

Just my $0.02, about 3 years ago, I stopped using the Carnauba wax that came with the system and now use Renaissance Wax, fewer fingerprints.

RC

ps. Don't use white diamond on Walnut! Cry
Back to top
« Last Edit: Mar 25th, 2017 at 2:01pm by Ron Carrabotta »  

It is easier to be forgiven than to get permission!
 
IP Logged
 
Steve Arnold
Active Member
***
Offline


WR Rocks!

Posts: 134

Burbank, California, USA
Burbank
California
USA

Gender: male

Jet 1640EVS
Re: Beall polishing system
Reply #2 - Mar 25th, 2017 at 2:08pm
 
Ron Carrabotta wrote on Mar 25th, 2017 at 1:36pm:
ps. Don't use white diamond on Walnut!


OMG, is that ever the truth! Undecided
Back to top
  
 
IP Logged
 
Bruce Kamp
Active Member
***
Offline


WR Rocks!

Posts: 173

Re: Beall polishing system
Reply #3 - Mar 25th, 2017 at 4:41pm
 
Good advice. I would guess that you get white in the grain, is that correct or is there another reason?
Back to top
  
 
IP Logged
 
Ken Vaughan
WR Moderator
*****
Offline


Still learning

Posts: 3,685

Juneau, Alaska, USA
Juneau
Alaska
USA

Gender: male

Stubby 750
Jet 1014 vs
Bonnie Klein Lathe

Re: Beall polishing system
Reply #4 - Mar 25th, 2017 at 5:53pm
 

Bruce, I have had Jerry's stuff for a long time.

I use a variable speed motor to drive the buffing wheels and bobs.  If you use the lathe, you likely have variable speed.

I also use different compounds when I am buffing out wood and when I am buffing a film finish applied to the wood. 

If buffing a film finish be very sure it is fully cured. 

I took a few buffing lessons from a buddy that makes mirror smooth surfaces on autos including making lacquer magic. 



Back to top
  
 
IP Logged
 
Ron Carrabotta
WR Supporter
*****
Offline


WR Rocks!

Posts: 363

Dawsonville, ga, Georgia, USA
Dawsonville, ga
Georgia
USA

Gender: male

Jet 1014 VS
Jet 1642 -2EVS
Powermatic 3520B
Re: Beall polishing system
Reply #5 - Mar 26th, 2017 at 10:12am
 
Bruce,

Yes, white in the grain. I don't use the white diamond on any dark colored open grained wood. Walnut, Mahogany....
Back to top
  

It is easier to be forgiven than to get permission!
 
IP Logged
 
Rick Caron
Active Member
WR Supporter
***
Offline


So many logs, so little
time!

Posts: 238

Greer, South Carolina, USA
Greer
South Carolina
USA

Gender: male
Re: Beall polishing system
Reply #6 - Mar 26th, 2017 at 12:23pm
 
I just stating using the beall system.  On a 6"  cherry bowl  i have a slight whitish haze on the inside.  Not near the top or the bottom, just in the middle.   I think it's  wax.   Can i run #0000 steel wool on that area, then rewax?
Back to top
  
 
IP Logged
 
Darryl Hansen
WR Supporter
*****
Offline


WR Rocks!

Posts: 41

Re: Beall polishing system
Reply #7 - Mar 26th, 2017 at 1:17pm
 
I always shoot a couple of coats of lacquer on my bowls then use the Beall disks. Never leave a white stain on anything dark or light. I use the buffs inside the bowls. Took the coarsest of the three disks off the three unit cause I don't finish uncoated wood.
Back to top
  
 
IP Logged
 
Bruce Kamp
Active Member
***
Offline


WR Rocks!

Posts: 173

Re: Beall polishing system
Reply #8 - Mar 26th, 2017 at 3:44pm
 
I see that tripoli is the coarsest grit of the three with white diamond and then wax being the others. I have been using Behlen's rottonstone, using mineral oil as a lubricant, as a way to get a final, rather glossy finish. For a more matt finish I have used Behlen's 2 pumice after the finish has cured for a week or more.
Behlen's rottonstone is also labeled tripoli. So, I guess my question is will I get the same gloss effect with the Beall tripoli buff as I would with the Behlen"s hand rubbed?
Darryl says he doesn't use the tripoli buff at all because he doesn't buff bare wood. Right now I plan on applying some sort of finish coat to each of my projects.  If I apply a gloss poly as a finish coat and then wait for it to cure what do I start with tripoli or white diamond?
Also, if, as Ron says, no white diamond on dark, open grain wood then what should I use? I understand this problem as I have tried McQuires polish in the past on padouk and had a bad experience.
Thanks
Bruce
Back to top
  
 
IP Logged
 
Arlin Eastman
Active Member
***
Offline


Born in the USA

Posts: 204

Council Bluffs, Iowa, USA
Council Bluffs
Iowa
USA

Gender: male

PM3520B
Re: Beall polishing system
Reply #9 - Mar 26th, 2017 at 6:33pm
 
Ron Carrabotta wrote on Mar 25th, 2017 at 1:36pm:
Bruce,

I've been using the Beall system since I got back into turning 7 years ago. I use it on almost all of my finished projects. I've also got the pads and mineral oil buffing system as well. Use the Beall 10x to1 vs the pads & oil. MUCH simpler.

Yes, for bowls get the separate buffs. You might want to consider getting both the wheels (original system) and the bowl buffs.

Just my $0.02, about 3 years ago, I stopped using the Carnauba wax that came with the system and now use Renaissance Wax, fewer fingerprints.

RC

ps. Don't use white diamond on Walnut! Cry



I also do like Ron said but I do use the Carnauba wax then put the buff on about 200rpm and apply the Renaissance Wax it comes out very nicely, however, all of it does not last along time or a lot of handling.

I also never use white diamond on dark woods unless I want the affects like adding the white lime paste.

To me I have some rotten stone and it does not feel or look the same.  JMHO
Back to top
  

It is always the right time; To do the right thing
 
IP Logged
 
Steve Doerr
WR Champion
*****
Offline


Wood is one of God's hidden /> canvases.

Posts: 719

Joplin, Missouri, USA
Joplin
Missouri
USA

Gender: male

Rikon 70-050VS
Jet 1642 EVS 2HP
Robust American Beauty
Re: Beall polishing system
Reply #10 - Mar 26th, 2017 at 9:08pm
 
Bruce,
To answer your question about bare wood versus finished wood.  You can use all three of them on either bare wood or wood with a finish.  Before I use the Beall buffs, I dip my turnings in oil. Once dry, I then use all three of the compounds to buff them out.  Remember when using the white diamond, you only put a very small amount on the buffing wheel while it is spinning.  I've been told the purpose of the white diamond is to remove the tripoli that gets on the wood from the first buffing.  I have also uses the tripoli and white diamond on my CA finishes.

I have found that the bowl buffs (the balls) don't do as good a job as the wheels.  I would suggest getting both sizes of buffing wheels.
Back to top
  
WWW  
IP Logged
 
robert baccus
Junior Member
*
Offline


WR Rocks!

Posts: 46

Gender: male
Re: Beall polishing system
Reply #11 - Mar 26th, 2017 at 9:45pm
 
The rotten stone--pumice thing is very primitive.  Use what car specialist's use--auto store liquid polishing compounds in various grits followed by liquid carnuba waxes.  Much easier and eliminates "burning".
Back to top
  
 
IP Logged
 
Bruce Kamp
Active Member
***
Offline


WR Rocks!

Posts: 173

Re: Beall polishing system
Reply #12 - Mar 27th, 2017 at 9:48am
 
Thank you everyone for the input. Your responses have taught me a lot. I have ordered the system, three separate buffs plus the bowl buffs.
I am excited to try it on a project that I had used Behlen's on that I was disappointed in.
I will post the results.
Back to top
  
 
IP Logged
 
Mike Nathal
WR Supporter
*****
Offline


WR Rocks!

Posts: 119

Strongsville, Ohio, USA
Strongsville
Ohio
USA

Re: Beall polishing system
Reply #13 - Mar 27th, 2017 at 5:18pm
 
If you use a penetrating oil like Tung or walnut, or an oil/varnish blend like Danish, you will probably need to be more aggressive with the Tripoli wheel.  (Higher speeds, larger diameter wheel).  If you are buffing a film finish like lacquer or water- or oil- base poly, you need to be more gentle (slower rpms, smaller wheels, less pressure).  I believe the white diamond wheel significantly refines the polish, it does more than just remove the tripoli residue. 
I love my Beall buffs but would like to experiment more with the auto store liquid polishing compounds, which only make sense on film finishes.  And will do so when my tripoli and white diamond bars are worn away, approximately 2019.   Smiley
Back to top
  
 
IP Logged
 
Gary D Baker
Full Member
**
Offline


WR Rocks!

Posts: 71

Re: Beall polishing system
Reply #14 - Mar 29th, 2017 at 7:06pm
 
I use 99.9% lacquer.  I have the beall system, but don't use it.  I apply three coats of lacquer, sanding at 400 between each coat to get a flat surface.  On the third coat I finish it off by buffing with 0000steel wool and renaissance wax ... then buff with a paper towel ... or towel ... whatever will buff it ... at 1,000 rpm ... and don't get it hot enough to melt the lacquer.

You will get a nice, rich shine that does not look like plastic and will be so welcoming to the touch that people won't put it down.
Back to top
  
 
IP Logged
 
Pages: 1 2 
Send Topic Print