Woodturner's Resource
Woodturner's Resource  
  • Featured Artist    • Websites   Support Wr
Tutorials, Projects & Tips   • Event Calendar   • Tool and Book Store
 

 

 
 
Welcome, Guest. Please Login or Register
amazon
  Home Page Forum HelpSearch Map TPT Resources LoginRegister
 
  The Woodturning Forum - Woodturner's Resource › Woodturning Forum › Segmented Woodturning › FIRST real attempt at segmented turnings
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1
Send Topic Print
FIRST real attempt at segmented turnings (Read 130 times)
 
Anthony Diorio
Active Member
***
Offline


WR Rocks!

Posts: 117

Staten Island, New York, USA
Staten Island
New York
USA

Jet 1221VS
FIRST real attempt at segmented turnings
Jun 19th, 2021 at 8:32am  
I haven't used my lathe much other than making some parts for models I was building.. I figured I'd give it a little workout.. .. I'm pretty happy with the way it turned out

Its 10" high about 5" wide 888 pieces
Back to top
« Last Edit: Jun 19th, 2021 at 11:21am by Anthony Diorio »  
 
IP Logged
 
Register To Remove Ads
Ed Weber
WR Administrator
WR Patron
*****
Offline



Posts: 8,440

Wilton, California, USA
Wilton
California
USA
Gender: male

JET 1642
Grizzly G0584
Re: FIRST real attempt at segmented turnings
Reply #1 - Jun 19th, 2021 at 8:52am  
Very nice for your first "real" attempt  Thumbs Up
Back to top
  
 
IP Logged
 
Anthony Diorio
Active Member
***
Offline


WR Rocks!

Posts: 117

Staten Island, New York, USA
Staten Island
New York
USA

Jet 1221VS
Re: FIRST real attempt at segmented turnings
Reply #2 - Jun 19th, 2021 at 9:25am  
Ed Weber wrote on Jun 19th, 2021 at 8:52am:
Very nice for your first "real" attempt  Thumbs Up


Thanks Ed..

I posted a question in tools section regarding play in lathe spindle.. would appreciate your imput.
Back to top
  
 
IP Logged
 
Robert Hayward
WR Addict
*****
Offline


WR Rocks!

Posts: 713

Tampa area, Florida, USA
Tampa area
Florida
USA
Gender: male

3520b
Re: FIRST real attempt at segmented turnings
Reply #3 - Jun 19th, 2021 at 11:23am  
That is a nice vase even if it was several attempts down the road. What are the dimensions?
Back to top
  
 
IP Logged
 
Anthony Diorio
Active Member
***
Offline


WR Rocks!

Posts: 117

Staten Island, New York, USA
Staten Island
New York
USA

Jet 1221VS
Re: FIRST real attempt at segmented turnings
Reply #4 - Jun 19th, 2021 at 12:29pm  
Robert Hayward wrote on Jun 19th, 2021 at 11:23am:
That is a nice vase even if it was several attempts down the road. What are the dimensions?


ts 10" high about 5" wide 888 pieces..
Back to top
  
 
IP Logged
 
Page Index Toggle Pages: 1
Send Topic Print
‹ Previous Topic | Next Topic ›
  « Home ‹ Board Top of this page

The Woodturning Forum - Woodturner's Resource » Powered by YaBB 2.5.2!
YaBB Forum Software © 2000-2021. All Rights Reserved.

Page completed in 0.7736 seconds.

Email:admin@woodturnersresource.com

Woodturners Resource ©
Rated #1 Among All The Woodturning Forums On The Net.
This is the place woodturners go to for the most up to date woodturning ideas.

Terms of Service  -  Privacy Policy